Mods if this isn't ok to put here just let me know it can be moved or deleted
so from probably one of the worst tut writers here is basics of the book.
several people have asked about the book (PM's, on DA and an email) so here is a real quick mini tut. its only covering the basics of getting a similar type book. No doubt using 3d by MKT you can do much the same, but this is how I did it without the plug in. This was never intended to be a tut as I didn't jot anything down as I went along. So for this I had to pull some shots from mockups, and some from my trash bin.......
The main questions I get asked is about how did I make it look so 3d and about how it looks so dreamy.
The depth in the book was from all the different shadow layers, and the end glow was mostly photo and curves, and some local contrast enhancements. Please do no ask me what settings I used for the dreamyness as I did 5 steps forward 10 back , 2 forward 3back etc etc. working on three different pdns for the book changing as I went along, until I was pleased.
One thing you should note is you should take great care on where your light source is, it should be same direction as the picture in the book. all light was from the upper left corner, so all shadows fell to the right and down when doing the pages in the book.
So from my trash bin, some partials pdn files and a few screen shots I'll try to reconstruct the basic book. I did have to put in some mock up pictures as the book was three pdns going at the same time. I tend to move back and forth between all three at the same time. so I had to try and write this as A) the cover B) the pages C) the picture
sure hope you can follow along.
A the cover. PDN #1
1) you need a big canvas size to accomadate the tilt. I used 1500 x 780 draw a rec 800 x 416 gradiant on this rectangle a leather color.
2) I knew the picture and pages were going in on the right so the left side was going to be a bit bare. I knew I needed something for the dream bubble to come out of so I did a rosace (separate layer) to cover that section.
3) the band is one of those things that came about after I was almost done. I undid undid and undid part of my 10 steps forward 5 back thing. for ease you should add it in now do it on a transparent layer
if you like how this all looks go ahead
4) flatten

5) now use layers to tilt it back. the only setting changes are 90 under twist angle and 30 under twist radius.
make a note this is same tilt everytime. 6) the book looks pretty slim so on yet another transparent layer I drew a line in just a slightly darker color than the book cover along the entire bottom edge and added a small dot along the bottom where the spine of the book is if its looking correct thickness go ahead and merge only the line and dot to the book cover

7) time to drop shadow. make a duplicate layer the drop shadow is done twice on the bottom of the two layers.
sorry I had to mock up this picture for you as I didn't keep a copy of the original untouched.
B the pages PDN #2
1) use same size canvas 1500 x 780 placement about where on the screen the right side of the book is.
2) make a page don't go too light and not too close to the cover color. this should be one half the book less a little bit
3) add a transparent layer do a varicose plugin wide strips

4) wand one of the strips move the selection to the edge of your paper
5) then go back down to the actual layer of your paper
and cut away,
this bit is tricky as you have to for each side of the paper cut off do selection on varicose layer move selection and then come down to paper to actually cut. I deleted the varicose layer at this point as I didn't need it any longer.
5) do a small drop shadow on the page layer.
6) duplicate that layer of paper move your selections so the page show just a bit along the outside edge add a few pages this way
so it should look something like this now.

7) flatten the pages together.

duplicate the flattened layer
9) tilt one layer back 90 under twist angle.
10 and drop shadow

11) leave the other layer as is. not tilted not drop shadowed this will be needed for along the bottom edge
12) on the un tilted layer move it 90 degree angle and down a few pixels so that you can see a stack of pages along the bottom

13) get rid of the excess using eraser on the untilted layer.

C the picture layer PDN#3
1) picture should be same size as the pages. same place on screen as the pages . Optional was the page curl . I thought that was an extra that gave even more depth. there is a tut in the tutorial section for that already. I modified that tut. Made my curl smaller so it didn't cut so much of my picture out.
2) a drop shadow under the picture. (optional)
3) text as ususal do it on a transparent layer so it can be moved around and changed. it was outlined several times.
I did aa on my text in this picture but the close up shot in my first post was taken prior to that step
4) added on yet another layer a band of x down the centre with a drop shadow to be the binding.
5) if you are please with it merge
6) tilt same settings 90 under twist angle
7) drop shadow.

now its just paste the one on top of the other each in a separate layer in case you have to move them around a bit. cover on the bottom layer , then the pages on next layer and then picture. if the placement is good merge together
now go ahead and use photo or glow or darken with curves, this is your book
so this was just a quick mini tut. thanks for thaking the time to read it sorry I didn't take any more screen shots as I went along.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,